他揉捏她两乳不停呻吟a片,亚洲国产成人精品无码区99,无码jk粉嫩小泬在线观看欧美,黑人上司粗大拔不出来电影

Online Service
Scan it
Support hotline
18681482740
Service Hotline:
18681482740
中文  |   English
Industry knowledge
Contact

Address: Floor 1, Building 2, Quanshengchang Industrial Park, Buyong Shajing Road, Shajing Street, Shenzhen

Contact: Mr. Li 18681482740

Email: lilinhan1314@126.com

Website: www.kotuajans.com

Industry knowledge
Processing requirements for precision stretching and stamping parts
07-26 / 2024

Precision stretch stamping parts are common accessories in hardware tools, so what are the processing requirements for them?


1. The shape of precision stretching and stamping parts should be as simple and symmetrical as possible: in the circumferential direction, axisymmetric stretching parts will undergo uniform deformation, and the mold used at this time is also relatively easy to process, and the processability is also the best. For stretched parts of other shapes, try to avoid sharp contour changes as much as possible. For example, the rear cover of a car muffler, while ensuring usage requirements, will simplify its shape and transform the production process from multiple processes to one to two processes, reducing material consumption by half.


2. The size ratio of each part of precision stretching and stamping parts should be appropriate: it should be avoided to design flanges and deep stretching parts as much as possible, as such parts require more stretching times. For example, the difference between the upper and lower dimensions of the workpiece is too large, which does not meet the requirements of the stretching process. To make it composite, it can be divided into two parts, processed and manufactured separately, and then connected. If the workpiece cavity is not deep, but the flange diameter is large, the manufacturing difficulty is also great, and annealing treatment is needed in the middle. If the flange diameter is reduced, intermediate annealing can be avoided. The contour of the workpiece flange should preferably be similar to the contour shape of the deep drawn part. If the width of the flange is not consistent, it will not only be difficult to stretch, but also require additional processes. It is also necessary to relax the edge cutting allowance and increase metal consumption.


3. The fillet radius of precision stretching and stamping parts should be appropriate: in order to facilitate forming and reduce the number of drawing times, the fillet radius of the stretching part should be increased as much as possible. The fillet radius between the bottom and wall of the stretched part, the flange and wall, and the four walls of the rectangular part must meet the requirements.


4. The uneven thickness phenomenon of precision stretching stamping parts should be considered: the inner and outer walls of the workpiece that has been stretched multiple times or the flange surface of the stretched parts with flanges should allow for imprints generated during the stretching process. Unless there are special requirements for the workpiece, shaping or shaping methods can be used to eliminate these marks.


5. The hole positions on precision stretching and stamping parts should be reasonably arranged: set the hole positions on the main structural surface of the stretching part to maintain it in a plane, or make the hole wall perpendicular to the plane, so that punching and trimming can be completed simultaneously in one process.




6. Selection of stretching oil: In addition to considering the lubricity and cooling properties of stretching oil, the rust resistance, cost, and ease of maintenance of stretching oil should also be considered in the selection of stretching oil. Stretch oil is easy to use base oil with relatively low viscosity and add wear reducing additives, which can achieve lubrication and friction reduction, as well as good cooling and easy filtration. However, the problem with stretching oil is its low flash point, high temperature during stamping forming, easy deformation, high risk factor, and fast volatilization, resulting in higher user usage costs. Therefore, it is recommended to choose stretching oil with high compressive and wear resistance when conditions permit.





7. The dimensional accuracy of precision stretching and stamping parts should not be too high: the manufacturing accuracy of stretching parts includes the accuracy in the diameter direction and the accuracy in the height direction. In general, the accuracy of precision stretching and stamping parts should not exceed the specified values. The dimensions on the product drawing need to be indicated to ensure external or internal dimensions, and cannot be marked with both internal and external dimensions.


Links:Zibo CNC machine tool automatic car washing machine Qingdao refrigeration equipment grinder equipment steel grit fire inspection cabinet sweeper motor desulfurization denitrification equipment drawing mold washing machine automatic soldering machine server repair HART475 hand operator dust-free cloth dust-free paper stack screw type Sludge dehydration machine, precision repair welding machine, Shandong motor repair, rotary hot pot equipment, integrated ultrasonic cleaning machine, Zhongjie radial drilling machine, beer equipment, Shenzhen brass manufacturer, welcome lamp, lens digging, drilling rig, aluminum housing manufacturer, automatic dispensing machine, automatic screwing machine neodymium Iron boron magnet 4g router wireless bridge
We provide you with high quality products
变态另类重口特级| [中文] [3d全彩h漫]新来的邻居| 青青草视频在线| 我和漂亮的妽妽激情| 书生屁股被cao成sao货男男| 啦啦啦资源视频在线观看8| 久久精品国产亚洲av四区| 黑色包臀裙秘书啪啪久久网站| 被主人在厨房用黄瓜调教| 无码av久久久久久久久| 欧美成人在线视频| 将军与娇妻各种做高h| 床震吃奶摸下成人a片在线观看| 邻居少妇张开双腿让我爽一夜| 69国产精品成人无码视频| 两根大肉大捧一进一出好爽视频| xxxx丰满小少妇女高潮| 久久久久精品国产三级美国美女| 无码少妇一区二区| 夜夜爽妓女8888视频免费观看| 大内密探零零性| 美女视频黄a视频全免费网站| 斗罗玉转漫画1—37免费漫画| 亚洲日本va中文字幕无码| 国产一区二区精品久久岳| 欧美free性xxxx护士hd| 香港三级午夜理伦三级三| 夜躁狠狠综合亚洲色噜噜狠狠| 无码亚洲一本aa午夜在线观看| 久久日日摸夜夜摸夜夜爽| 在线观看国产一区二区三区| 公与3个熄乱理在线播放| 公交车上~嗯啊被高潮| 欧美老妇人与黑人做爰| 囯产极品美女高潮无套久久久| a片大全| 金瓶悔1一5扬思敏完整版| 久久精品国产亚洲av四区| 大肥波bbwwhbbww| 曰批视频免费40分钟试看| 人人澡人摸人人添学生av|